Belar FMMA-1

In stock

Original price was: $ 4,929.18.Current price is: $ 4,700.71.
Weight 5.4431 kg
features

MEASUREMENTS:

Total Peak Modulation in Percent
Peak Modulation expressed in kHz Deviation
Peaks-per-Minute Count
Loop-thru #1 Modulation
Loop-thru #2 Modulation
Peak Average Modulation
Average/Peak Modulation Ratio
Peak Minimum Modulation
AM Noise (with Option 02)
Synchronous AM Noise (with Option 02)
RF Level (with Option 02)
Pilot Modulation (requires FMS-2 or other source of filtered pilot)
Pilot Injection (requires FMS-2 or other source of filtered pilot)
SCA Injection (requires SCM-2 or other source of filtered SCA)

 
SETTABLE PARAMETERS:

Hold Time
Peak Modulation Indicator
Peaks-per-Minute Indicator
Display Hold
Display Blanking
Peaks-per-Minute Duration
Remote Enable
Audio Failure Alarm – Time & Modulation
Loop-thru #1 Gain (+20% Modulation)
Loop-thru #2 Gain (+20% Modulation)
Display Resolution (01% or 1%)
Time Mode (Real/Past)
Peak Weighting (8 time constants)
Calibrator (with Option 01)

specification

SPECIFICATIONS:

Accuracy:
0.1%

Display:
Large 4 digit LED for Total Modulation

,

16 segment alphanumeric LED display for menus and parameters

Input:
Composite or 650 Khz IF (with Option 01) for use with

Belar RFA-4

,

RFA-1A

,

or DC-4

,

or RF transmitter sample (with Option 01 and Option 02)

Option 01:
Precision FM Demodulator with Calibrator

Input:
650 kHz IF (From RFA-4

,

RFA-1A

,

DC-4

,

or Option 02)

Output:
Two 75 ohm buffered

,

composite

Signal/Noise:
> 95dB

Distortion (IM):
< 0.003%

Distortion (THD):
Unmeasureable (< 0.01%)

Option 02:
Down Converter and Synchronous AM Noise Detector

Frequency Range:
88 to 108 MHz Std. (Specify frequency)

Input:
1-10 volts rms

,

50 ohms

,

BNC connector

Outputs:
650 kHz IF

,

9-pin D connector to Wizard

Signal/Noise:
> 95 dB

AM Noise Range:
-17 to -80 dB

Synchronous AM Noise Range:
-17 to -80 dB

Ship Separately

0

Product can be split into multiple boxes

0

Belar FMHD-1

In stock

Original price was: $ 8,664.61.Current price is: $ 8,253.37.
Weight 6.8039 kg
features

Frequency Agile Antenna and High Level Inputs
RF Spectrum Analysis with Mask and Sideband Power Measurements
Metering of Analog Total

,

Pilot

,

L

,

R

,

L+R

,

and L−R
Metering of HD L

,

R

,

L+R

,

L−R Audio
Time Alignment Graphic Display Analysis ±16384 samples

,

±375 ms to ±256 samples

,

±5.8 ms Audio Polarity
Level Alignment Graphic Display Analysis ±20.0 dB
HD Control and Status Information
HD SIS and PAD Data
BER (Bit Error Rate) Measurements

specification

RF Inputs

Antenna Input
87.5 to 108 MHz Frequency Agile

75 Ω

,

F Connector

RF Inputs
87.5 to 108 MHz Frequency Agile

1 to 10 Vms

,

50Ω

,

BNC Connector

Composite Outputs

Analog (2)
+1.5 Vms@100%

,

75Ω Unbalanced

BNC Connector

Digital (2)
LVDS

,

100Ω

,

RJ-45

Audio Outputs

Analog (8 Channel Assignable)
+10 dBm

600Ω Balanced

,

XLR Connector

AES-3ID (6 Channel Assignable)
1.0 Vp-p

75 Ω

,

BNC Connector

Headphone (L/R Assignable)
1/4” Phone Jack

Computer Interface

RS-232
9 pin Male D Sub Connector

Ethernet 10/100 Base-T
RJ-45 Connection

Alarms

Relays(4 Assignable)
Form C

,

15 pin Female D Connector

Dimensions
2 EIA Rack Unit

Power Requirements
40 Watts

,

100-240V

,

50/60 Hz

Shipping Weight
15 lbs

Ship Separately

0

Product can be split into multiple boxes

0

Solidyne AudiMax 362HD

In stock

Original price was: $ 1,964.82.Current price is: $ 1,867.72.
Weight 5 kg
Product can be split into multiple boxes

0

Ship Separately

0

specification

Technical Specifications

Analog Input
XLR3 conector

,

level self-adjusted -6 dBu to + 15 dBu Z= 600 / 10 Kohms

,

balanced

Analog Output Balanced

,

+ 4 dBu Z= 600 / 10 Kohms

,

with de-emphasis (flat response)

MPX Output
600/10 Kohms

,

factory set level to standard 4 Vpp Differential output

,

BNC connector

,

floating ground 50 ohms Allows 45 dB canceling buzz & noise due to ground loops

Frequency Response
20 – 16.000 Hz +/- 0

,

5 dB measured below compression & limiter threshold

Harmonic Distortion
Below 0

,

02 % @ 30-15.000Hz

Noise
Below – 90 dBA ref 100 % modulation

Stereo Separation
> 75 dBA

Subsonic Filter
Chebyshev 2nd order

,

15 Hz

Asymmetry
Cancelling 5 : 1 cancelling effect

,

using Khann-Bonello system

Expander
10:1 slope

,

0

,

1 msec attack time

,

200
msec release

AGC (wideband)
VCA controlled

,

30 dB range

,

3 sec attack/release

Multiband Compressors
3 bands

,

18 B/octave

,

Linear Phase crossover. Compressors: 30 dB range

,

5:1 slope

,

VCA controlled Automatic attack time. Release time user controlled by 3 x ENERGY controls

IM Cancelled
Clipper IM clipper cancellation > 30 dB below 250 hz

Dynamic EQ
0 – 12 dB dynamic boost at Low

,

Mid and High Frecuency Front panel user controlled

Processing
7 stages of processing devices

Power
115 V / 230 V (rear switch selected) 50/60 Hz

,

20 W

Dimensions
19" rack mount. Module one (44

,

4 mm).

Solidyne 542APC

In stock

Original price was: $ 3,929.63.Current price is: $ 3,741.15.
Weight 5 kg
Product can be split into multiple boxes

0

Ship Separately

0

specification

Technical Specifications

Analog Input
600/10 K balanced XLR 50 dB CM Rejection 20-15 Khz. Input level selected by software in 1 dB steps. Sigma-Delta converters 24 bits / 192 Khz

Digital Input
Optional AES-3 digital balanced input Z=110 ohms. Automatic selection of 32

,

44

,

1

,

48

,

96 & 192 Khz with sample rate converter (128 dB Dynamic Range

,

-117 dB THD) to avoid jitter

Analog Output
600 balanced XLR

,

output level +4 dBm Sigma-Delta converters 24 bits / 192 Khz

Digital Output
Optional AES-3 digital balanced output

,

Z=110 ohms FS=48 or 96 Khz

,

selected by software

MPX Output
From 2 Vpp to 5 Vpp in 0.2 steps

Processing Technology
DSP (Digital Signal Processing). Total CPU power 2.700 MIPS

MPX Post-Processing
SuperModulation exclusive Solidyne technology

,

at 608 Khz oversampling. Fast clipper DC-10 Mhz wideband channel to avoid audible artifacts

Frequency Response
20-15.000 Hz +/-0.25 dB. Flat mode XLR out or digital AES-3 Out. Output without pre-emphasis

Harmonic Distortion (THD)
THD below 0.008 % (30-15 Khz

,

Flat Mode)

Noise
Dynamic Range= 95 dBA

Stereo Separation
75 dBA @ 1 KHz: > 65 dBA @ 30-15.000 Hz

Subsonic Filter
Chebyshev FC=20 Hz 25 dB rejection at 10 Hz

Asymmetry Canceling
Phase processing technology with Kahn-Bonello algorithms. Cancelling Factor=8:1

Linear Expander
Range=20 dB Attack & Release time software controlled

Gated Wide-Band AGC
Range=30 dB. Attack / Release time & Threshold controlled from LCD screen

Multiband Compressors
DSP controlled. Five Bands

,

Crossover= 24dB/oct Max compression = 30dB. Slope = 10:1

Compressors Attack/Release Time
Attack and Release controlled separately

IM Canceled Clipper
IM canceling factor : greater than 30 dB below 250 Hz

Fast Clipper
Four channels

,

absolutely alias free using DC-10 Mhz bandwidth channel

Density Equalizer
Four bands density equalizer with 15 dB range at the output of multiband compressors

Low pass filter
15 Khz digital low pass FIR filter

,

60 dB rejection at 19 Khz

Storage of Preset Settings
30 programs that can be changed on-air from PC computer using the 462dsp serial port

RS-232 PC control
RS232 serial port. It can be connected to USB bus with optional external adapter. Optional Ethernet bus connection

Super Modulation
MPX processing for stereo interleaving

,

allows for 130% L & R audio level at 100% modulation

RS-232 PC control
Yes. It includes free Windows 2000/XP software

AM FM compatible
The user can change the processor's AM/FM firmware chips. Only two socket mounted Flash EPROM IC's have to be replaced. Stereo coder is a separate module

Processing Bands and stages
Five processing bands / Nine processing stages

LCD Display
Blue color

,

LCD display with backlight. Graphic type Resolution 240 x 64

RDS Encoder
Optional built in RDS encoder

Power
90/127V and 190/230V; 50/60 Hz

,

selectable from rear panel

Dimensions
483 mm Wide 240 mm Deep

,

88 mm High

Solidyne 2600

In stock

Original price was: $ 12,417.18.Current price is: $ 11,823.17.
Weight 2 kg
Product can be split into multiple boxes

0

Ship Separately

0

specification

Specifications

Audio Inputs
2 (two) stereo inputs each module;

One balanced stereo line (or mono Mic in 2610 & 2612); and one unbalanced AUX.

Option USB 2602

,

2 stereo Digital inputs & 2 stereo Digital outputs by USB

Inputs Level/Impedance
Balanced MIC= -25 dBu/-80 dBu; 150/250 Ohms

Balanced LINE = -20 dBu/+22 dBu; 600~ 10Kohms

Unbalanced AUX = -20 dBu/+15dBu; 600~ 10Kohms

Inserts for both MIC inputs in microphone modules.

Stereo insert for LINE A in LINE modules.

Phantom 48v
Standard phantom 48V power supply for up to 10 microphones.

Outputs
3 bus outputs; PGM & AUD balanced + 4 dBm;

AUX Unbalanced + 4 dBm

Balanced Outs; Max Level +26dBu (10K)

,

+20dBm (600ohms)

Unbalanced Outs; Max Level = +20dBm/600 ohms

Optional Digital AES/EBU output for PGM & AUD.

Digital Levels
AES-3/SPDIF outputs TCP/IP & USB inputs & outputs; 0VU RMS is set at -15dB Ref Full Scale level. 0dB Peak is set to 100% Full Digtal Scale

Monitor & Hybrid Outputs
1 Separate Hybrid CUE

,

+4dBu / 10K

1 Hybrid On-Air Receive + 4 dBu/10K

1 Hybrid send (MIX-Minus) +4 dBu / 10K

CUE Monitor
Internal Monitor Amplifiers: 3W CUE monitor with internal speaker. 2 Stereo Monitor outputs; Control Room & Studio

,

with Muting Relays (line level).

Microphone Processor
Optional MIC module model 2612

,

160mm wide

,

with 3 MIC with processing facilities. 4 band EQ

,

80 Hz and 10 kHz shelving

,

160 Hz & 5 kHz bell shaped; +/- 14 dB action. Expander Gate to eliminate backgound noise. Audio Compressor

,

20 dB action. Iluminated switchs for EQ and Compressor-Expander

Monitor & Hybrid Outputs
1 Separate Hybrid CUE

,

+4dBu / 10K

1 Hybrid On-Air Receive + 4 dBu/10K

1 Hybrid send (MIX-Minus) +4 dBu / 10K

Headroom
22 dB @ LIN to PGM Ref + 4dBu/10 k

Digital Control Bus
One Start Devices output for each input module

,

to start external devices when open each channel fader. Out at minijack 1/8" // Ring = A channel (left side) Tip= B channel (Rigth side) Open collector OFF = Open Manages 0-24 V DC @ 100 mA

Frequency response
20-20.000 Hz +/- 0.25 dB (LIN or MIC to PGM)

Noise
MIC input

,

EIN=-132 dBu/150 ohms

LINE input

,

S/N > 95 dBA at PGM output

Dynamic Range
From Line to PGM > 110dBA (Better than CD quality)

Crosstalk
PGM-AUD-SEND > 90 dBA @30-10.000 Hz

L-R & R-L > 80 dBA @ 1khz

Distortion
From LINE to PGM out < 0.01 % THD @30-15.000 Hz

From MIC to PGM out < 0.01 % THD @30-15.000 Hz

Phase
From Line to PGM

,

< 2º L&R @50-10.000 Hz

Stereo tracking
Below 0.2 dB error L/R in fader range 0 to 40 dB

Phone Hybrid
3 Hybrid inputs

,

2 for phone lines and one for cellular phone at 4 wires.
It includes a mini-PBX with Ringer

,

Line attention with free hands operation

,

and Line Transfer.

Talkback Microphone
Included Talkback MIC

,

with Audio Limiter. Noise Cancelled PZM type / Outputs to Phone Line Hybrid and Studio Speaker with AutoSwitch (AutoSwitch allows one-touch Studio communication)

VU-meters
2600XL: 4 digitally controlled VUmeters 24 steps of 1 dB

,

DUAL type (RMS & Peak) for PGM & AUD. One Timer/Clock and one
Stereo Phase Vector display

Timer /Clock Option
Timer counts minutes: seconds during on-air MIC in order to avoid excessive speaker on-air time When the Timer is off

,

a standard clock is activated

ON-AIR Signal
ON-AIR signal output (turns on when MIC is open) 12 VDC @ 0

,

3 amp

Start external devices
One Start Devices output for each input module

,

to start external devices when open each channel fader. Out at minijack 1/8" // Ring = A channel (left side) Tip= B channel (Rigth side) Open collector OFF= Open. Manages 0-24 VDC @ 100 mA. This allows to control Virtual Rack processors and start audio devices.

Power
110-127 V / 190-240V

,

with switch

,

50/60 hz

,

80 VA

Dimensions & Weight
XL model: 840 wide x 585 depth x 135 height – Weight 15 Kg

BOX : 90 x 65 x 25 cm

,

2 Kg

2600XD: 845mm wide

,

635mm depth

,

125 mm height – Weight 15 Kg

BOX: 90 x 70 x 20 cm

,

2 Kg

Solidyne D612

In stock

Original price was: $ 3,409.87.Current price is: $ 3,244.23.
Weight 4.7 kg
Product can be split into multiple boxes

0

Ship Separately

0

specification

D612 Digital & Analog Console

Audio Inputs
4 balanced MIC inputs (XLR)

2 balanced stereo Line inputs (DIN 5)

3 unbalanced stereo Line inputs (RCA)

1 Digital stereo Line input (USB)

Inputs Level & Impedance
Balanced MIC= -10 dBu/-75 dBu; 150 / 250 Ohms

Balanced LINE = -20 dBu / +26 dBu; 600~ 10Kohms

Unbalanced LINE = -15 dBu / +12 dBu; 600~ 10Kohms

Phantom Power
Two MIC inputs have 48 V phantom power supply

,

switchable ON / OFF

Analog Outputs
2 bus stereo outputs; PGM (6

,

35mm

,

TRS plug) & REC (RCA connector)

Both at + 4 dBm = 0 VU

PGM balanced: Max Level +26dBu (10K)

,

+20dBm (600 ohms)

REC unbalanced

,

Max level 20 dBu

External Hybrid: unbalanced Mic-Minus out at + 4 dBu

Digital USB Input / Output
USB digital In/Out; Input to channel 5; Output to PGM or REC

It uses the K15 Overload recommendation for broadcating;

Then

,

0 VU is at -15 dB Full Scale level

ON-AIR Signal
ON-AIR Tally Light output (turns on when MIC is open)

12 V CC @ 0

,

12 amp (two Solidyne On-Air lights)

Monitor & Hybrid Outputs
1 Stereo Studio

,

0 dBu for active speakers

,

muted

1 Stereo Control

,

0 dBu for active speakers

,

muted

1 Stereo Studio Headphones

,

with Distribution AMP

up to 5 headphones

,

+ 10 dBu

1 Stereo Control Headphones

,

+ 10 dBu

1 External Hybrid send (MIX-Minus) +4 dBu / 10K

CUE Monitor
Internal CUE Monitor Amplifier; 250 mW

,

with speaker included

Headroom
22 dB @ LIN to PGM Ref + 4dBu/10 k

Frequency Response
20-20.000 Hz +/- 0.25 dB (LIN to PGM)

20-20.000 Hz +/- 0

,

5 dB (MIC to PGM)

MIC Equalizer
Four Bands MIC EQ with In/Out switch; 80 Hz top flat curve

,

160 Hz bell shaped

,

4 kHz bell shaped

,

8 kHz top flat curve

Action + 15 dB / -15 dB

MIC Compressor
Low distortion MIC compressor with In/Out switch. 20 dB max compression. Attack time < 10 ms.

Threshold = 0 VU

Compression ratio: < 2 dB variation for 15 dB change MIC level

Noise
MIC input

,

EIN=-120 dBu / 150 ohms

LINE input

,

S/N > 75 dBA

Dynamic Range
From Line to PGM > 90 dBA (CD quality)

Crosstalk
PGM-REC > 65 dBA @ 1 kHz

Distortion
From LINE to PGM out < 0.03 % THD @30-15.000 Hz

Phase
From Line to PGM

,

< 3º L&R @50-10.000 Hz

Stereo Tracking
Below 0.2 dB error L/R in fader range 0 to 40 dB

Telephone Hybrid Specs
Two channel telephone active Hybrid:

One phone line plus one cellular (Bluetooth linked)

Frequency Response: 200 – 5.000 Hz

Noise: > 60 dBA S/N

Rejection: > 35 dB rejection

NULL adjust in front panel preset

Preference atenuator: 12 dB local announcer interrupt priority

Telephone input lightning discharge safety
Telephone Hybrid input is transformer floating to meet the Public Telephone Service isolation standards. It is protected with SIOV Varistors against soft lightning discharges.

External gas discharge protection is recommended

Talkback Microphone
Included Talkback MIC

,

with Audio Limiter. Noise Cancelled PZM type.

Outputs to Phone Line Hybrid or Studio Speakers & Headphones.

VU-meters & Compression Level
2 x LED VUmeters for PGM. Cuasi peak reading

Microphone compressor level meter 0 – 15 dB

AoIP Optional TCP / IP Digital Streaming Output
Ethernet RJ45 connection to a standard LAN (Option /AoIP)

Used for sending D612 output to transmitter plant with MP3 Internet streaming or using a 5

,

8 GHz 802. Link

Also can be used for AoIP connection with another console located inside or outside studios

It can work in linear PCM at 44.1 & 48 kHz or MP3 VBR

On-Air information using GPIO for remote processors

AoIP Delay and user modes
MP3 Layer 1 (32

,

44.1 and 48 kHz)

MP3 Layer 2 (16

,

22.05 and 24 kHz)

16bit PCM uncompressed (8

,

16

,

32

,

44.1 & 48 kHz)

Full duplex (transmitting and receiving)

Delay using PCM at 48 kHz Fs (recommended) Less than 5 mS

Delay using MP3 streaming. Average 100 mS

Power
Switching external power supply 90-240 V

,

20VA [28V@0

,

57A]

Dimensions & Weight
Wide: 405 mm; Deep: 385 mm; Height: 95 mm at rear turret

Net Weight: 4.7 Kg

features

8 channels

,

with 5 faders with connectors (used to change it without soldering)
12 stereo inputs:

                  4 balanced MIC                   2 LIN balanced (DIN 5)

,

                   3 LIN unbalanced (RCA)

,

                   1 digital input USB

,

                   2 Hybrid telephone (RJ11 & Bluetooth)

,

                   1 Monitor Air (Jack 6.35 mm)

4 outputs stereo; 
a) Digital: A digital stereo USB output

,

selectable PGM or REC 
b) Analog: Program (PGM) balanced & Recordings (REC) unbalanced External Hybrid (In / Out).
5 Monitor Stereo Outputs

,

with muting logic; Speakers Studio

,

Studio Headphones (with Distributor Amplifier)

,

 
Control Speakers

,

Headphones Control

,

CUE mono (with amplifier and internal speaker). 
4 Band EQ Mic
Microphone Audio Compressor
Low Silhouette

,

flush mounting on any table without cutting it
Hybrid with Bluetooth wireless cellphone
Professional Attenuators 100mm Conductive Ceramic 15-year life
Option AoIP to transmit digital audio over Ethernet / Internet
External switching power supply: 90-240 V / / 50 / 60 Hz Output: 28 V 0

,

55 A

Sonifex RB-DS2

In stock

Original price was: $ 2,130.45.Current price is: $ 2,027.64.
Weight 2.3 kg
specification

Technical Specification For RB-DS2

A/D Specification

Maximum Input Level:
+28dBu

Input Impedance:
> 10kΩ bridging

Analogue & Digital Input Levels:
Selectable +12dBu

,

+18dBu

,

+24dBu for FSD

Analogue Pre-set Input Gain Range:
Adjustable 3dB loss to 3dB gain (L & R adjust)

Signal to Noise:
Better than -101dBFS (RMS A-weighted at 24bit)

Dynamic Range:
> 110dB

Distortion & Noise:
> 96dB THD + N at 1kHz

D/A Specification

Maximum Output Level:
+24dBu

Output Impedance:
< 50Ω

Dynamic Range:
> 100dB

Analogue Output Gain Range:
Selectable -6dBu to +24dBu output level

,

ref FSD

Sampling Frequency:
Selectable 32kHz

,

44.1kHz

,

48kHz 64kHz

,

88.2kHz or 96kHz

Sample Width:
Selectable 16bit or 24bit

Channels:
Stereo or dual mono

Format (Fields & Frames):
PAL

,

NTSC

Delay Units:
Samples

,

fields

,

frames

,

milliseconds

,

hh:mm:ss

,

(with CF expansion)

Maximum Delay:
10.5 seconds @ 96kHz

,

24bit

,

stereo (excluding memory expansion)

Rear Panel Connections

Analogue Inputs:
2 x XLR 3 pin female (balanced) (L & R)

Analogue Outputs:
2 x XLR 3 pin male (balanced) (L & R)

Digital Inputs:
1 x AES/EBU XLR 3 pin female

Digital Outputs:
1 x AES/EBU XLR 3 pin male

Remote I/O Port:
15-way ‘D’-type plug

,

8 GPI inputs

,

4 GPI outputs

Serial Comms Port:
9-way ‘D’-type plug

Memory Expansion:
Internal Compact Flash™ storage card supporting up to 2GB. CF cards must be PIO Type 4 or higher.

Mains Input:
Filtered IEC

,

continuously rated 85-264 VAC

,

47-63Hz

,

fused

,

60W peak

,

30W average

Fuse Rating:
Anti-surge fuse 2A 20 x 5mm

Front Panel Controls

Display:
Vacuum fluorescent display

System Navigation:
Rotary selector with integral push-switch

Audio Bypass:
Via push-button

Equipment Type

RB-DS2:
Stereo delay synchroniser & time-zone delay

Physical Specification

Dimensions (Raw):
48cm (W) x 15.8cm (D *) x 4.2cm (H) (1U)

19” (W) x 6.2” (D*) x 1.7” (H) (1U)

Dimensions (Boxed):
59cm (W) x 27.5cm (D*) x 11cm (H)

23.2” (W) x 10.8” (D*) x 4.3” (H)

Weight
Nett: 1.6kg Gross: 2.3kg

Nett: 3.5lbs Gross: 4.8lbs

Ship Separately

0

Product can be split into multiple boxes

0

Sonifex Monitor Stands

In stock

Original price was: $ 188.49.Current price is: $ 177.06.
Product can be split into multiple boxes

0

Ship Separately

0

Sonifex Net-Log

In stock

Original price was: $ 4,803.52.Current price is: $ 4,563.63.
Weight 4 kg
Dimensions 55 × 28 × 17 cm
Product can be split into multiple boxes

0

Ship Separately

0

specification

Technical Specification For Net-Log

Audio Specification

Input Impedance:
>10kΩ balanced.

Maximum Input Level:
+20dB.

Distortion:
<0.1% @ 1kHz + 16dBu.

Signal to Noise Ratio:
90 dB RMS A wtd. 22kHz bandwidth.

Wow and Flutter:
Unmeasurable.

Phase Error at 10kHz:
Unmeasurable.

Rear Panel Connections

,

Controls and Indicators

Analogue Inputs:
4 x XLR 3 pin socket.

Input Level Controls:
4 x Rotary pre-set potentiometers.

Network:
RJ45 10Mbps ethernet.

Network Status LEDs:
Rx

,

Tx

,

link and collision.

RS232:
2 x 9 way D-type plug.

Alarm Outputs and Remote Inputs:
15 way D-type plug.

Power:
IEC Power plug

,

95-265 VAC

,

47-63Hz.

Controls and Indicators

Front Panel Controls:
Record control to instantly start recording

Front Panel Power Indicator:
Power LED (blue)

Front Panel Alarm Indicators:
2 x Alarm LEDs

,

disk drive alarm LED (red)

,

archive alarm LED (red)

Front Panel Level Indicators:
4 x Analogue input level LED

,

1 for each channel (green

,

orange

,

red)

Rear Panel Network Indicators:
4 x LEDs

,

receive (RX)

,

transmit (TX)

,

link and collision LEDs

Additional Information

Sample Rates:
16kHz

,

22.05kHz

,

24kHz

,

32kHz

,

44.1kHz and 48kHz

Audio Format:
Mpeg layer 2 with bit-rates as below and G.729 low bit rate

Recording Types:
Mono

,

dual mono

,

stereo

Hard Disk Capacity:
A minimum hard-disk size of 1TB is fitted. The maximum size of hard-disk that can be used in this product is 2TB.

PC Soundcard Needed:
Any windows compatible soundcard that can play PCM (.wav) audio files

Equipment Type

Net-Log-01
Net-Log 4 channel audio logger

,

with large hard disk

(contact sales@sonifex.co.uk for current sizes available)

Net-Log-Win01
Net-Log Windows™ software – 2 stream licence.

Net-Log-Win05
Net-Log Windows™ software – 5 stream licence

Net-Log-UPS01
1U rack-mount UPS for use with Net-Log

Net-Log-G729
G.729 software licence for one Net-Log (up to 4 mono channels).

Physical Specification

External Dimensions:
1U 19” rack x 22cm deep 48cm (W) x 22cm (D) x 4.2cm (H) (1U)

1U 19” rack x 8.7” deep 19” (W) x 8.7” (D) x 1.7” (H) (1U)

Boxed Dimensions:
55.2cm (W) x 29.5cm (D) x 16.5cm (H)

21.7" (W) x 11.6" (D) x 6.5" (H)

Weight:
2.5kg – 5.5lbs

features

Key Features of Net-Log

Dedicated reliable multi-channel recording hardware.
Easy to use Windows™ remote operation for playback

,

archiving

,

streaming and configuration.
Independently configurable channel pairs to record at different sample rates

,

different bit rates and in mono or stereo.
Recording duration configuration of the channels to suit your needs

,

e.g. 2 channels of low quality logging for 12 months together with two channels of high quality logging for 1 month

,

on one machine.
Record inputs can be controlled remotely

,

e.g. snoop recording from mic-live output of a mixer.
Automated voice recording – each channel can start and stop recording automatically by setting audio threshold levels

,

which means that it can be used for voice controlled systems and telephony recording.
Up to 250

,

000 recordings per channel can be made.
Each Net-Log has its own IP address

,

so a number of machines can be installed on the same network.
Fail-safe alarm indicators and remotes.
Password protection and security access rights to system.
Support for hard disk sizes up to 2048GB.
Recordings can be made using optional G.729 algorithm

,

allowing longer recordings and lower network traffic. G.729 audio quality is comparable to MPEG L2 at 32kbits/sec when used to record/playback speech.
Recording on Net-Log can be controlled serially by Crestron and Televic board room controllers.

Label Dipole Antenna System

In stock

Original price was: $ 1,039.52.Current price is: $ 982.41.
Weight 15 kg
Dimensions 140 × 15 × 15 cm
video

0

Product can be split into multiple boxes

0

Ship Separately

0

specification

Antenna type:
Dipole

Polarisation
Vertical or Horizontal 

Frequency range
87.5 – 108 MHz 

Impedance
50 Ohm 

V.S.W.R.
<1.25:1 

Antenna system gain
3 db 

Bandwidth
Broadband 

Antenna connector
"N-type" & 7/16" available 

Power divider input connector
"N-type"

,

7/16" or EIA7/8" as necessary 

Max antenna power input
Max 3kW with EIA7/8" connector

Max system power input
Max 1.6kW with N-type

,

2kW with 7/16" & 6kW with EIA7/8" connector

Antenna dimensions
1400 x 850 x 60 mm 

Combined antenna weight
9 kg 

Color

Black

Label Italy Circular Polarized FM Antenna System

In stock

Original price was: $ 1,496.46.Current price is: $ 1,427.92.
Weight 15 kg
Color

Black

specification

Antenna type:
Circular 'wideband'

Polarisation
Circular 

Frequency range
87.5 – 108 MHz 

Impedance
50 Ohm 

V.S.W.R.
<1.25:1 

Gain
3 db 

Bandwidth
Broadband 

Antenna connector
"N-type"

,

7/16" & 7/8"  available

Power divider input connector
"N-type"

,

7/16" or 7/8"  as necessary

Max antenna power input
Max 3000 W with 7/8" connector 

Max system power input
Max 1600 W with N-type

,

4000 W with 7/16" & 6000 W with 7/8" connector

Antenna dimensions
1520 x 1240 x 1150 mm 

Combined antenna weight
18 kg 

Ship Separately

0

Product can be split into multiple boxes

0

video

0

StationPlaylist Creator

In stock

Original price was: $ 177.06.Current price is: $ 165.64.
Weight 0.5 kg
Dimensions 10 × 10 × 10 cm
Color

Black

features

Creator Features:

Maximum number of daysa playlist may be generated in advance.
Related Artist support. Several artists may be treated as one artist as far as Artist Repeat Protection is concerned.  eg. John Cougar

,

John Cougar Mellencamp

,

John Mellencamp.
Related Title support. 2 or more songs with the same tune but with a different title may be treated as one title as far as the Title Repeat Protection is concerned.  This is particularly useful for Christmas songs.
Advanced Playlist Editor
Generate personalized HTML playlists for your website or intranet.  Staff

,

remote voice tracking DJ's

,

and/or listeners can see what has played and is yet to play.  DJ's can see the selected songs for their shift wherever they are in the world.
Global separation rules to prevent too many tracks of the same genre

,

tempo

,

mood

,

energy

,

gender

,

or decade being played too close together.
Track Rating Priority enables tracks with a poorer rating to be selected less often than other tracks.
Recycle Category Tracks will take the songs used during one period of the day and recycle them in another period of the day

,

giving the impression of a larger music library.
Linked Artists for scheduling 2 or more tracks by the same artist in the same hour for special purposes. May contain spots or jingles between the selected tracks.
Last Track Bias attempts to select the last song in the hour to fit as close as possible with the remaining time. Can produce hours within a few seconds of 60 minutes.
Voice Tracking System Easily and quickly record and insert voice announcements into the playlist.  This makes your station sound 100% live when unattended in automation mode. Voice tracking provides a way for a DJ to pre-record a show spanning several hours within a few minutes.StationPlaylist Studio Pro supports playing voice tracks simultaneously with the beginning (ramp) of the next song

,

so this combination provides a seamless "live" show for the listener

,

when completely automated/unattended.
Traffic/Billing log file import Supports all major traffic/billing commercial scheduling software including Natural Log

,

AdMaster

,

The Traffic Light

,

Radio Traffic

,

Radio Works for advanced management of advertisements.
Music log file import Converts 3rd party music scheduler logs into the format StationPlaylist Studio requires. Has been utilized with Music 1

,

PowerGold

,

RCS Selector

,

Natural Music

,

etc.
Advertising (Spot) Summary A summary of the advertising spots scheduled in the playlist is generated as a spreadsheet compatible file

,

which may also be printed.  This may be used for billing purposes.
Password protection A master password may be applied to prevent all access to Creator. A password may also be applied to protect against creating a playlist

,

and a 3rd password to limit who can edit playlists.
Maximum song categories (eg. music genres

,

tempos)
Maximum spot groups (ads

,

jingles

,

etc)
Maximum rotations (hourly templates of categories/spots)
Maximum schedules (daily templates of rotations used for each hour of each

Ship Separately

0

Product can be split into multiple boxes

0

video

0

StationPlaylist Studio

In stock

Original price was: $ 177.06.Current price is: $ 165.64.
video

0

Product can be split into multiple boxes

0

Ship Separately

0

features

Studio Features:

Live Assist mode
Track Preview / Cueing
Line Input control
Microphone control
Single key keyboard controls
Insert

,

delete & move tracks in the live playlist
48 slot cart machine for instant jingles
96 slot cart machine
Play Carts via push buttons
2 Users
Unlimited Users
Automation mode
Run unattended indefinitely
Advanced automatic crossfading using one soundcard
Voice track / song ramp overlapping
Auto Speed function
Sound processing – Compressor / Limiter
Replay Gain
Internet streaming
Stream Server Metadata Integration
Additional metadata output
Stream Listener Statistics
Website Song Requester
Include "Now Playing" details on your website
Earn money from music sales
Read existing file tags
Custom file tags
External I/O device integration
Automated satellite feeds
Station networking
Break Note support
Timed Events
Automated time-of-day announcement support
Automated temperature announcement support
Detailed logging of songs played
Detailed logging of spots played
Failsafe redundancy using Studio Monitor
Record audio to file
Cue Sheets
Password protection
Plays all major audio file formats
Play Internet streams/files
Plays several video formats
Global Clock Offset
API support for Developers
12 months free updates and email support
High Accessibility

Color

Black

Tannoy Reveal 502

In stock

Weight 5 kg
Color

Black

features

<h2>Features: Front</h2>
<ul>
<li>1" soft-dome “Poke-Resistant” tweeter</li>
<li>5" custom high-efficiency LF woofer</li>
<li>Accurately tuned front-firing bass port -allows near-wall placement and ensures optimal LF performance</li>
</ul>
<h2>Features: Rear</h2>
<ul>
<li>Balanced and unbalanced inputs for maximum flexibility</li>
<li>Plug in your phone /tablet for instant listening gratification</li>
<li>Adjust volume and EQ to match your listening environment</li>
<li>75 Watt Bi-Amp module and active crossover filter ensures maximum power and tonal clarity</li>
<li>Rubber padded base for acoustical isolation</li>
</ul>

specification

<table class="product-tab-table">
<tbody>
<tr><th class="product-tab-table-category" colspan="2">General</th></tr>
<tr>
<td width="45%" class="product-tab-table-header">Frequency Response</td>
<td class="product-tab-table-header">49 Hz -43 kHz</td>
</tr>
<tr>
<td class="product-tab-table-header">Max SPL</td>
<td class="product-tab-table-header">108 dB</td>
</tr>
<tr><th class="product-tab-table-category" colspan="2">Membrane Sizes</th></tr>
<tr>
<td class="product-tab-table-header">LF/Mid Range</td>
<td class="product-tab-table-header">5" (130 mm)</td>
</tr>
<tr>
<td class="product-tab-table-header">HF</td>
<td class="product-tab-table-header">1" Soft Dome (25 mm)</td>
</tr>
<tr><th class="product-tab-table-category" colspan="2">Bi-amp Output Power

,

RMS</th></tr>
<tr>
<td class="product-tab-table-header">Power Output</td>
<td class="product-tab-table-header">75 Watts</td>
</tr>
<tr>
<td class="product-tab-table-header">LF/Mid Range</td>
<td class="product-tab-table-header">50 Watts</td>
</tr>
<tr>
<td class="product-tab-table-header">HF</td>
<td class="product-tab-table-header">25 Watts</td>
</tr>
<tr>
<td class="product-tab-table-header">THD</td>
<td class="product-tab-table-header">< 0.7 %</td>
</tr>
<tr><th class="product-tab-table-category" colspan="2">Input Types and Impedances</th></tr>
<tr>
<td class="product-tab-table-header">Balanced</td>
<td class="product-tab-table-header">XLR

,

20 kOhm</td>
</tr>
<tr>
<td class="product-tab-table-header">Unbalanced</td>
<td class="product-tab-table-header">¼" Jack

,

10 kOhm</td>
</tr>
<tr>
<td class="product-tab-table-header">AUX Link</td>
<td class="product-tab-table-header">Mini Jack

,

10 kOhm</td>
</tr>
<tr>
<td class="product-tab-table-header">AUX Link Output</td>
<td class="product-tab-table-header">Mini Jack</td>
</tr>
<tr><th class="product-tab-table-category" colspan="2">EQ Options</th></tr>
<tr>
<td class="product-tab-table-header">HF EQ Settings</td>
<td class="product-tab-table-header">-1.5 dB HF Cut / Neutral / +1.5 dB HF Boost</td>
</tr>
<tr>
<td class="product-tab-table-header">Crossover Frequency</td>
<td class="product-tab-table-header">2.3 kHz</td>
</tr>
<tr>
<td class="product-tab-table-header">Low Frequency Alignment</td>
<td class="product-tab-table-header">Optimized Front Port</td>
</tr>
<tr><th class="product-tab-table-category" colspan="2">Cabinet Dimensions</th></tr>
<tr>
<td class="product-tab-table-header">HxWxD

,

inches</td>
<td class="product-tab-table-header">11.8 x 7.2 x 9.4</td>
</tr>
<tr>
<td class="product-tab-table-header">HxWxD

,

mm</td>
<td class="product-tab-table-header">300 x 184 x 238</td>
</tr>
</tbody>
</table>

Ship Separately

0

Product can be split into multiple boxes

0

video

0

Tannoy Reveal 802

In stock

Color

Black

features

<h2>Features: Front</h2>
<ul>
<li>1" soft-dome “Poke-Resistant” tweeter</li>
<li>8" custom high-efficiency LF woofer</li>
<li>Accurately tuned front-firing bass port -allows near-wall placement and ensures optimal LF performance</li>
</ul>
<h2>Features: Rear</h2>
<ul>
<li>Balanced and unbalanced inputs for maximum flexibility</li>
<li>Adjust volume and EQ to match your listening environment</li>
<li>Plug in your phone /tablet for instant listening gratification</li>
<li>100 Watt Bi-Amp module and active crossover filter ensures maximum power and tonal clarity</li>
<li>Rubber padded base for acoustical isolation</li>
</ul>

specification

<table class="product-tab-table">
<tbody>
<tr><th class="product-tab-table-category" colspan="2">General</th></tr>
<tr>
<td width="45%" class="product-tab-table-header">Frequency Response</td>
<td class="product-tab-table-header">42 Hz – 43 kHz</td>
</tr>
<tr>
<td class="product-tab-table-header">Max SPL</td>
<td class="product-tab-table-header">114 dB</td>
</tr>
<tr><th class="product-tab-table-category" colspan="2">Membrane Sizes</th></tr>
<tr>
<td class="product-tab-table-header">LF/Mid Range</td>
<td class="product-tab-table-header">8" (200 mm)</td>
</tr>
<tr>
<td class="product-tab-table-header">HF</td>
<td class="product-tab-table-header">1" Soft Dome (25 mm)</td>
</tr>
<tr><th class="product-tab-table-category" colspan="2">Bi-amp Output Power

,

RMS</th></tr>
<tr>
<td class="product-tab-table-header">Power Output</td>
<td class="product-tab-table-header">100 Watts</td>
</tr>
<tr>
<td class="product-tab-table-header">LF/Mid Range</td>
<td class="product-tab-table-header">75 Watts</td>
</tr>
<tr>
<td class="product-tab-table-header">HF</td>
<td class="product-tab-table-header">25 Watts</td>
</tr>
<tr>
<td class="product-tab-table-header">THD</td>
<td class="product-tab-table-header">< 0.4 %</td>
</tr>
<tr><th class="product-tab-table-category" colspan="2">Input Types and Impedances</th></tr>
<tr>
<td class="product-tab-table-header">Balanced</td>
<td class="product-tab-table-header">XLR

,

20 kOhm</td>
</tr>
<tr>
<td class="product-tab-table-header">Unbalanced</td>
<td class="product-tab-table-header">¼" Jack

,

10 kOhm</td>
</tr>
<tr>
<td class="product-tab-table-header">AUX Link</td>
<td class="product-tab-table-header">Mini Jack

,

10 kOhm</td>
</tr>
<tr>
<td class="product-tab-table-header">AUX Link Output</td>
<td class="product-tab-table-header">Mini Jack</td>
</tr>
<tr><th class="product-tab-table-category" colspan="2">EQ Options</th></tr>
<tr>
<td class="product-tab-table-header">HF EQ Settings</td>
<td class="product-tab-table-header">-1.5 dB HF Cut / Neutral / +1.5 dB HF Boost</td>
</tr>
<tr>
<td class="product-tab-table-header">Crossover Frequency</td>
<td class="product-tab-table-header">1.8 kHz</td>
</tr>
<tr>
<td class="product-tab-table-header">Low Frequency Alignment</td>
<td class="product-tab-table-header">Optimized Front Port</td>
</tr>
<tr><th class="product-tab-table-category" colspan="2">Cabinet Dimensions</th></tr>
<tr>
<td class="product-tab-table-header">HxWxD

,

inches</td>
<td class="product-tab-table-header">15.4 x 10.0 x 11.8</td>
</tr>
<tr>
<td class="product-tab-table-header">HxWxD

,

mm</td>
<td class="product-tab-table-header">390 x 254 x 300</td>
</tr>
</tbody>
</table>

Ship Separately

0

Product can be split into multiple boxes

0

video

0