BW Broadcast TX1000 V3
1kW Digital FM Transmitter
The BW Broadcast TX1000 V3 takes the legendary and clean exciters of earlier models with its ultra-low distortion modulator to a new level. The TX1000 V3 has an integrated multi-band DSPX audio processor that means stations without a dedicated processor sound great, right out of the box. This market-leading DSP based multi-channel audio processor has been designed to give you a major market signature sound on a budget. With both four band program dependent limiting and wide band AGC with intelligent gating, parametric EQ and shelf bass enhancement, multi-band distortion controlled clipper and a powerful composite clipper with pilot protection. All this allows you to tailor your sound for maximum impact. Integrated ITU-R 812 MPX power limiter ensures you meet modulation regulations.
For years, our transmitters have been the most intelligent on the market with standard Ethernet Remote Control. Featuring a built-in web browser, with no software to install and no reliance on flash support, the V3 platform gives you easy access to setup and monitoring such as Email Alerts, SNMP monitoring, Silence Detection, Advanced Alarms. The unit will email you if it has a problem, and keep a log of any issues to be investigated. You can also adjust settings remotely if required. All these features are designed to give you peace of mind and save you time.
A standard, configurable parallel GPI/O interface is provided for interfacing to your station remote control equipment. This will alert you to issues and offer solutions to keep you on air. For example, it can be configured to switch on backup audio or backup transmitters should it detect a problem.
All V3 products have inputs and outputs you would come to expect with a premium Transmitter. Featuring AES3 audio or composite/ MPX over AES192, analogue left and right, and 2 configurable composites (MPX) program inputs and outputs. Composite inputs and outputs can be configured as MPX, SCA, RDS or Pilot Sync.
FSK ID Keyer as a standard for translators removes the need for external hardware or hourly audible announcements and offers broadcasters a one-box solution for their translator sites.
Integrated Dynamic RDS is now standard onboard. Listeners now expect to see RDS data on their radios featuring full station, music and advertising related information. The V3 platform includes a powerful dynamic RDS system allowing you to maximize the impact, and deliver value for your advertisers from a single box solution.
External reference support for both 1pps and 10MHz GPS sync inputs are at the rear of the unit, letting you integrate with other products for an SFN (single frequency network) environment. Hot-pluggable, simple to replace switch-mode power supplies with 96% ACDC efficiency. Combining rock-solid reliability, performance and simple maintenance to keep you on the air.
- 30-1100 watts RF output power
- Direct to channel digital modulation
- GPS inputs for SFN application
- XLR analogue & digital inputs
- Dual MPX / sca in and outs
- Lab grade DSP stereo generator
- RDS generator
- DSPX multi-band processor inside
- VSWR and temp monitoring
- Slide-in & Hot-swap power supplies
- Events, alarms and actions
- RS232, Telnet, SNMP
- Mobile-ready web browser control
- Harmonics:better than -75 dBc
- Frequency range:87.5 - 108 MHz
- Frequency steps:10KHz to 100KHz selectable
- Frequency selection: User interface or web remote control
- Frequency control type: direct to channel DDS
- Frequency stability:<+/- 100 Hz
- Modulation: DDS
- Synchronous AM Noise:>60dB% min (at normal deviation)
- Asynchronous AM Noise:>70dB
- RF Connector:7/16 EIA
AUDIO & MPX I/O
- MPX input / output connector:2 X BNC IN / 2 X BNC OUT
- MPX input / output impedance:10k
- MPX input level:-10dB to +10dB (adjustable)
- MPX input / output response:+/- 0.01 dB, 5 Hz to 100 kHz
- Audio input connectors:XLR balanced
- Analog input impedance:10 kOhm
- AES/EBU sampling rates:32KHz-192KHz (MPX OVER AES READY)
- Subcarrier generation:DSP
- Pilot:19 kHz +/- 1 Hz (adjustable)
- Output level:0dBu - 12dBu adjustable
- 15 kHz filtering:80dB at 19kHz (DSP based)
- Overshoot filter clipping:DSP based
- Spurious: >80 kHz / >160kHz:> -60dBr / > -80dBr
- Stereo separation:>50dB (20Hz - 15kHz)
- RF Power:100W - 1100W
- Voltage input:100-265 VAC
- Environmental:1275W average @ 1000W RF
- Switched mode approvals:UL / TUV / CE
- Size (mm):483mm x 450mm x 89mm
- Weight:8.4 kg
- User Interface:3 buttons, rotary encoder & 256x64 graphics display
- External control:I/O Alarms D9-type Male; RS232 D9-Type Female
- Telnet and Web remote RJ45 Ethernet
TRU Price Guarantee
(Subject to conditions)